Overview Specifications Operability, Display and
Analytical Functions Various Software Options

Digital Oscilloscope "ViewGo II" DS-5600A Series Specifications

  DS-5654A DS-5652A DS-5634A DS-5632A DS-5624A DS-5622A DS-5614A DS-5612A
Frequency bandwidth (-3dB) 500MHz 350MHz 200MHz 100MHz
Rise time
(Representative values)		 750ps 1ns 1.75ns 3.5ns
Number of input channels 4 2 4 2 4 2 4 2
Maximum sampling speed 2GS/s (when channels are coupled), 1GS/s (when all channels are used)
Equivalent sampling speed 100GS/s
Peak detection resolution 1ns
Averaging function 2 to 65536 times (power of 2 steps)
Averaging
Count display function 		Display the number of executions on the screen.
Memory length 5M points/ch (when 2 channels are coupled), 2.5M points/ch (all channels)
Vertical resolution 8 bits (when high resolution arithmetic is enabled: up to 12 bits)
Vertical resolution display function Display the number of resolution bits
Input voltage range 2mV/div ~ 10V/div(1MΩ)
2mV/div ~ 2V/div(50Ω)
Offset voltage 2mV/div ~ 50mV/div : ±1V, 50.2mV/div ~ 500mV/div : ±10V, 502mV/div ~ 10V/div : ±100V
DC gain accuracy ±(1.5% +0.5% full-scale)
Maximum input voltage ±400 VpeakI (1MΩ), 5 Vrms(50Ω)
Bandwidth limit filter Analog type:100MHz, 20MHz, 2MHz, 200kHz Analog type:20MHz, 2MHz, 200kHz
Digital type: Choose either LPF, HPF, or SMA, channel independent
Input coupling GND, DC 1MΩ, AC1MΩ, DC50Ω
Input impedance 1MΩ±1% //16pF, 50Ω±1%
Probe sense Auto search:1:1, 10:1, 100:1, 1000:1
Manual setting:1:1, 5:1, 10:1, 20:1, 50:1, 100:1, 200:1, 500:1, 1000:1, 2000:1
Time axis range 500ps/div ~ 50s/div 1ns/div ~ 50s/div 2ns/div ~ 50s/div 5ns/div ~ 50s/div
Standard probe SS-101R (with standard number of channels) SS-0130R (with standard number of channels)
Roll mode 50ms/div ~ 50s/div (100kS/s max)
Clock accuracy ±10 ppm
Trigger function
Trigger function Edge, Edge Alternate, Edge OR, Number of Pulses, Pulse Width, Period, Missing, TV, Pattern (OR, NOR, AND, NAND),
Serial (UART, SPI, I2C)
TV trigger (standard)/
Line setting range selection/
Field selection		 NTSC, PAL, Custom/up to 3000/1, 2, 4, 8
Pulse number trigger setting range 1 to 9999 events
Pulse width trigger time setting range 15ns~50s
Cycle trigger time setting range 40ns~50s
Missing (dropout)
Trigger time setting range		 50ns~50s
Pattern trigger  OR, NOR, AND, NAND
Trigger source/
State/
Threshold level		 All channels/HIGH, LOW, Don't Care/Independent setting for all channels
Serial trigger UART Trigger selection START, STOP,Parity error, data pattern Comparison data length 5 to 8 bits
Bit rate 1000bps~１Mbps
(Set in 100bps units)		 Signal source CH1~CH4, EXT
(2-channel device is CH1, CH2, EXT)
Serial trigger UART Trigger selection Data pattern Comparison data length 4 to 64 bits
CS selection Positive logic/Negative logic,
Idle time specification when there is no CS		 Signal source CH1~CH4, EXT
(2-channel device is CH1, CH2, EXT)
* CH1 input is for SCK signal input only: up to 20MHz
Serial trigger I2C Trigger selection START, STOP, RESTART, NACK,Data pattern Comparison data length 7-bit/10-bit address, 1 to 5 bytes,
EEPROM read, byte (shift comparison available)
Address mode Choose from 7-bit/10-bit/EEPROM read Signal source CH1~CH4, EXT
(2-channel device is CH1, CH2, EXT)
Trigger source All channels, EXT (±0.5V), EXT10 (±5.0V), line
Trigger slope/
Coupling		 Positive, negative/AC, DC, high frequency removal, low frequency removal, noise removal
Display/Resolution
Display/Resolution 7.5-inch color TFT LCD (touch screen)/VGA:640 × 480 pixels
Display format YT, XY, XY Trigger
Vector connection Sample point interpolation display, dot display
Analog
persistence		 Solid tone display, spectrum display
Persistence
Display time		 100ms, 200ms, 500ms, 1s, 2s, 5s, 10s,Infinite
Save internal waveform
(REF memory)		 5 waveforms
Front panel settings save Five settings can be saved in the internal memory or USB memory device
AUTO SETUP function Can be set to Enabled or Disabled
Parameter measurement, cursor, zoom, math, replay
Parameter measurement Maximum value, minimum value, peak value, RMS value, cycle RMS value, average value, cycle average value, top, base, top-base, rising overshoot, falling overshoot, rising time 20-80%, falling time 80-20%, rising time 10-90%, falling time 90-10%, frequency, cycle, number of pulses (positive), number of pulses (negative), pulse width (positive), pulse width (negative), duty ratio, integral, skew (positive/negative), skew @ level
Number of simultaneous measurements/
Statistical values display		 Maximum 4 parameters/maximum value, minimum value, number of measurements
Logging items, output destination Time, parameter measurement results (conditions A, B, C, and D), Pass/Fail judgment results
When recording: Pop-up screen, internal memory (up to 86,400), after recording: USB memory device
Pass/Fail Judgment mode: parameter judgment or mask determination, judgment result: USB save, BEEP sound,
pulse output, logging
Page search function: select Pass or Fail, search forward or backward
Cursor Time, Amplitude, Time & Amplitude, Value at Cursor
Zoom Press the Zoom button on the front panel to display the magnified waveform in a different grid
Math function Addition, subtraction, multiplication, differentiation, integration, FFT (up to 8k points, rectangular, Hanning, flat top window function)
Double operation by either differential, integral, or FFT from the result of either addition, subtraction, or multiplication (9 patterns)
Rescale/unit conversion a * x + b (x: input voltage, a, b: user-defined)/volt, ampere, watt, °C, no display
Replay Automatic waveform recording, up to 2048 waveforms can be saved and replayed
Frequency counter 6-digit
Interface USB 2.0HS compatible (device, host), LAN (100Base-TX),
GPIB (factory option DS-576), AUX interface (connector for external option)
AUX OUT Trigger output and pass/fail judgment output can be switched
Waveform data save Save to USB memory device with binary, ASCII, Mathcad, arithmetic (ASCII), and arithmetic (Mathcad)
Hard copy output Save the image to a USB memory device in TIFF, BMP, or PNG (Transparent) format
or output to a PictBridge® -compatible printer
Calibration signal output Square wave 1kHz, 3Vp-p
Power supply/power consumption AC100V ~ 240V(50Hz / 603Hz), AC100V ~ 120V(400Hz) / 95VA max(60W max)
Dimensions/Body weight Approx. 330Wx190Hx124D mm/Approx. 3.7kg
Environmental conditions
Performance warranty temperature 10 ~ 35℃
Operating temperature/humidity/altitude Temperature 0 to 40°C/Humidity 5 to 80% RH ≤ 30°C (no condensation),
55% RH or less 40°C (no condensation)/Altitude 2000m or less
Standard Accessories
Probes (one for each channel), power cord (1), front panel cover (1), manual (CD-ROM) (1), user's guide (1)
Option
AUX IO CH1/CH2 output
DS-577
(Factory option)		 AUX IO1: Output CH1 input signal with offset voltage added, AUX IO2: Output CH2 input signal with offset voltage added
AUX IO CH1 output
DS-578
(Factory option)		 Aux IO1: Output CH1 input signal with offset voltage added
GPIB interface
DS-576
(Factory option)		 GPIB: IEEE488.2
Probe power supply
DS-579		 IWATSU ELECTRIC active probe power supply 2 Series